i used the 5.64MB driver version, run it in WinXP Compatibility Mode and it worked :) Don't plug camera before installing it, and do reboot after done, then plug it and windows will complete operation.
(During installation process, at about 60% an alert box appeared telling me program stopped work, i pressed "close program" and installation resumed normally)
Based on the first comment, I downloaded the drivers, went to device manager, found a USB camera in the list with an error. Right clicked and chose "Update driver software". Browsed to the ../13178_01/89_2k_xp folder and clicked next, and got a message telling me theat "windows could not find driver software". Didn't understand the later comments about running as an admin in compatibility mode though? There was no option for this . . .?!
Tried the 5.64mb version, and had the 60% alert thing come up, cleared it and it continued ok. Rebooted, but still no good.
You're missing that on the setup file you could right click with your mouce. from there you can choose run as admin (or something similar) when you do that you can also choose advanced run features like the compatibility thing. Set it too winXP and you should be fine.
1 try: - download 1.98mb version - right click on file and click compatibility tab (windows xp) - Unzip into default folder C:\download.... - Connect Webcam - Go to device manager - Click update driver and point to folder in c:\download - message: "windows could not find driver blablabla"
2nd try: - download large file from trust side (5.xx mb) - Run compatibility xp, one big file in download.... - Again, run this big file (setup file) in compatibility mode. - Software/drivers are installed, don't have message with 60%. - restart computer - Connect webcam... Still same error
2.run it (it will unzip) 3.go to the destination folder (where it unzipped itself) 4.click on the unzipped Setup.exe file with RIGHT!!! mouse button 5.select Properties 6.Go to Compatibility tab 7.check box Run this program in compatigility mode for Windows XP (service pack 3) 8.press APPLY and then OK 9.click on the Setup.exe again with RIGHT!!! mouse button and select Run as Administrator, then confirm OK, if it ask you. 10.Then it will install itself. 11. Plug the cam, and it shoud work. 12. Enjoy
2.run it (it will unzip) 3.go to the destination folder (where it unzipped itself) 4.click on the unzipped Setup.exe file with RIGHT!!! mouse button 5.select Properties 6.Go to Compatibility tab 7.check box Run this program in compatigility mode for Windows XP (service pack 3) 8.press APPLY and then OK 9.click on the Setup.exe again with RIGHT!!! mouse button and select Run as Administrator, then confirm OK, if it ask you. 10.Then it will install itself. 11. Plug the cam, and it shoud work. 12. Enjoy
2.run it (it will unzip) 3.go to the destination folder (where it unzipped itself) 4.click on the unzipped Setup.exe file with RIGHT!!! mouse button 5.select Properties 6.Go to Compatibility tab 7.check box Run this program in compatigility mode for Windows XP (service pack 3) 8.press APPLY and then OK 9.click on the Setup.exe again with RIGHT!!! mouse button and select Run as Administrator, then confirm OK, if it ask you. 10.Then it will install itself. 11. Plug the cam, and it shoud work. 12. Enjoy
I got windows 7 64bit and driver from trust website installed for me only the webcam built-in microphone. Webcam was as device without driver.
Then i found this: http://blog.thepcmechanic.org/?p=30
I downloaded HCLASSIC-Vista-x64-V2.4 driver, run the installer and went to "C:\Users\YOURUSERNAME\AppData\Local\Temp" where looking through folders with long names i found one with file: HCLASSIC.INF. I copied folder with that file on desktop, killed the installer and edited this .inf file changing PID in line: %USB.DeviceDesc% = OVT.PCamMic.v64,USB\VID_05A9&PID_4519 to PID_8519&MI_00 and USB.DeviceDesc="Hercules Classic Webcam" to "trust 320 spacecam". saved the file, went back to device manager, clicked update driver and pointed to the folder with edited HCLASSIC.INF and BAM! camera works.
Great, but these steps don't work on Windows 10 since there's certificate protection saying: "The hash for the file is not present in the specified catalog file. The file is likely corrupt or the victim of tampering."
To be more specific: the file "hclassic.cat" contains the driver IDs signed with a certificate - and I think... this is the end :-(
isn't workin
ReplyDeleteDid you run it as an admin in compatability mode? (i.e. windows xp) It worked for me.
ReplyDeletei used the 5.64MB driver version, run it in WinXP Compatibility Mode and it worked :)
ReplyDeleteDon't plug camera before installing it, and do reboot after done, then plug it and windows will complete operation.
(During installation process, at about 60% an alert box appeared telling me program stopped work, i pressed "close program" and installation resumed normally)
Simply GREAT!!!!!, thanxs from Italy
ReplyDeleteBased on the first comment, I downloaded the drivers, went to device manager, found a USB camera in the list with an error.
ReplyDeleteRight clicked and chose "Update driver software". Browsed to the ../13178_01/89_2k_xp folder and clicked next, and got a message telling me theat "windows could not find driver software". Didn't understand the later comments about running as an admin in compatibility mode though? There was no option for this . . .?!
Tried the 5.64mb version, and had the 60% alert thing come up, cleared it and it continued ok. Rebooted, but still no good.
What am I missing?
You're missing that on the setup file you could right click with your mouce. from there you can choose run as admin (or something similar) when you do that you can also choose advanced run features like the compatibility thing. Set it too winXP and you should be fine.
ReplyDeleteThx for the comments all it helped me a lot.
I've got the same problem as Anonymous:
ReplyDeleteThings I tried:
1 try:
- download 1.98mb version
- right click on file and click compatibility tab (windows xp)
- Unzip into default folder C:\download....
- Connect Webcam
- Go to device manager
- Click update driver and point to folder in c:\download
- message: "windows could not find driver blablabla"
2nd try:
- download large file from trust side (5.xx mb)
- Run compatibility xp, one big file in download....
- Again, run this big file (setup file) in compatibility mode.
- Software/drivers are installed, don't have message with 60%.
- restart computer
- Connect webcam... Still same error
Any ideas?
hm...i tried both drivers with win xp compatible modus and i tried it as admin.
ReplyDeletei have win 7 HP(64bit)
can somebody help me?
Looks like it does not work with 64 bit windows 7.
ReplyDeleteNice post and this mail helped me alot in my college assignement. Say thank you you for your information.
ReplyDeletemany thanks - i downloaded short version, ran in xp compatability mode then plugged in and driver detected and worked
ReplyDeleteStep by step:
ReplyDelete1. download http://trust.cordoba.cdn.lukkien.com/publicpreview/13178/drivers_1113157/native_exe/16006183
2.run it (it will unzip)
3.go to the destination folder (where it unzipped itself)
4.click on the unzipped Setup.exe file with RIGHT!!! mouse button
5.select Properties
6.Go to Compatibility tab
7.check box Run this program in compatigility mode for Windows XP (service pack 3)
8.press APPLY and then OK
9.click on the Setup.exe again with RIGHT!!! mouse button and select Run as Administrator, then confirm OK, if it ask you.
10.Then it will install itself.
11. Plug the cam, and it shoud work.
12. Enjoy
Step by step:
ReplyDelete1. download http://trust.cordoba.cdn.lukkien.com/publicpreview/13178/drivers_1113157/native_exe/16006183
2.run it (it will unzip)
3.go to the destination folder (where it unzipped itself)
4.click on the unzipped Setup.exe file with RIGHT!!! mouse button
5.select Properties
6.Go to Compatibility tab
7.check box Run this program in compatigility mode for Windows XP (service pack 3)
8.press APPLY and then OK
9.click on the Setup.exe again with RIGHT!!! mouse button and select Run as Administrator, then confirm OK, if it ask you.
10.Then it will install itself.
11. Plug the cam, and it shoud work.
12. Enjoy
Step by step:
ReplyDelete1. download http://trust.cordoba.cdn.lukkien.com/publicpreview/13178/drivers_1113157/native_exe/16006183
2.run it (it will unzip)
3.go to the destination folder (where it unzipped itself)
4.click on the unzipped Setup.exe file with RIGHT!!! mouse button
5.select Properties
6.Go to Compatibility tab
7.check box Run this program in compatigility mode for Windows XP (service pack 3)
8.press APPLY and then OK
9.click on the Setup.exe again with RIGHT!!! mouse button and select Run as Administrator, then confirm OK, if it ask you.
10.Then it will install itself.
11. Plug the cam, and it shoud work.
12. Enjoy
Does not work for me :(
ReplyDeleteWant to use my spacecam!
Someone has another solution?
I got windows 7 64bit and driver from trust website installed for me only the webcam built-in microphone.
ReplyDeleteWebcam was as device without driver.
Then i found this: http://blog.thepcmechanic.org/?p=30
I downloaded HCLASSIC-Vista-x64-V2.4 driver, run the installer and went to "C:\Users\YOURUSERNAME\AppData\Local\Temp" where looking through folders with long names i found one with file: HCLASSIC.INF. I copied folder with that file on desktop, killed the installer and edited this .inf file changing PID in line: %USB.DeviceDesc% = OVT.PCamMic.v64,USB\VID_05A9&PID_4519 to PID_8519&MI_00 and USB.DeviceDesc="Hercules Classic Webcam" to "trust 320 spacecam". saved the file, went back to device manager, clicked update driver and pointed to the folder with edited HCLASSIC.INF and BAM! camera works.
I am using the trust 120 spacecam and can't get it to work yet.
ReplyDeleteIs this also possible with my camera?
I'm using windows 7 ultimate 64 bit
I am using the trust 120 spacecam and can't get it to work yet.
ReplyDeleteIs this also possible with my camera?
I'm using windows 7 ultimate 64 bit
Vicktor , you're a fucking genius ! thanks mate, you saved my trust spacecam 320 , i love you
ReplyDeletevictor, you're a fucking genius , you saved my day and my trust 320 spacecam, love you bro ;)
ReplyDeleteguys follow vicktor instructions, it work perfectly.
Great, but these steps don't work on Windows 10 since there's certificate protection saying:
ReplyDelete"The hash for the file is not present in the specified catalog file. The file is likely corrupt or the victim of tampering."
To be more specific: the file "hclassic.cat" contains the driver IDs signed with a certificate - and I think... this is the end :-(